powceq - توريد الأفران الحرارية لطلاء المعادن الآلي واليدوي
لماذا يجب أن تعمل معنا؟
فريق ديناميكي شاب، يتمتع بخبرة تزيد عن 12 عامًا في المتوسط. مصنعون متعددون لإفادة العملاء، إنتاج مثالي. فرق متعددة معدة دوليًا. يتم استخدام ماسحات ضوئية ثلاثية الأبعاد مبتكرة
أوقات تسليم أقصر بالأشهر حديثة للغاية وفعالة وجاهزة للتسليم
أنظمة طلاء المسحوق الصناعية الآلية
MDF Wood powder coating
MDF Powder coating equipment
MDF powder coating process
Low cure powder coatings
يمكننا تقديم الاستشارات الفنية فيما يتعلق بخطوط الإنتاج الأوتوماتيكية ومعالجة المشاكل الفنية في خطوط الإنتاج
تواصل
طلاء المسحوق هو أسلوب تشطيب شائع يتضمن وضع مسحوق جاف على السطح ثم معالجته باستخدام الحرارة. للحصول على طلاء مسحوق عالي الجودة، من الضروري أن يكون لديك المعدات المناسبة. يمكن أن تختلف معدات الطلاء بالمسحوق اعتمادًا على حجم الأجزاء المطلية وتعقيدها، بالإضافة إلى حجم الإنتاج. أيقونة أسفل
الإمارات العربية المتحدة
أوروبا بأكملها وسويسرا وألمانيا والنمسا
وعلاوة على ذلك، في جميع القارات
الشرق الأوسط، أفريقيا، أستراليا، آسيا، الولايات المتحدة الأمريكية، أمريكا الجنوبية
معدات وأفران بودر كوتنج
- Gema, Nordson, Wagner...
ما هو دهان البودرة ؟
طلاء البودر كوتنج
يعد طلاء البودركوتنج PC طريقة مثالية. إذا كنت ترغب في تحقيق تطابق لون معين. يمكن تطبيقه على مجموعة. من الركائز بما في ذلك الفولاذ والنحاس والألمنيوم ويوفر تشطيبات معمارية. متينة. مناسب لكل من التطبيقات الداخلية والخارجية. يتطلب الأخير معدنا صعيئا، وفي بعض الحالات عملية. معالجة. إضافية. للتعامل مع البيئات المالحة. يمكن لفريق الخبراء لدينا تقديم المشورة بشأن طريقة الإنهاء الأكثر ملاءمة لتطبيقك.
In addition to the spray gun, a powder coating system will also include a powder feed system and a control unit. The powder feed system delivers the powder from the hopper to the spray gun, while the control unit regulates the flow of powder and controls the electrostatic charge.
Powder center
Powder feed center
6 Variations
Reduces powder consumption and cleaning time
PLC controlled
Pump system
Transfer Pump
High Efficiency
After the powder has been applied, it must be cured using heat. Curing ovens are used to heat cure parts after they have been coated with powder. These ovens come in various sizes and can be powered by electricity or gas. The size of the oven needed will depend on the size of the parts being coated and the volume of production.
Powder curing oven
Box type electrical or gas / oil heated
Subsidized or box-shaped designs
Energy-efficient and productive
Perfect insulation and minimal heat loss
Homogeneous air distribution
Continuous ovens
Tunnel
U-Turn or special designs
Precise technology & intelligent solutions
Other equipment that may be used in a powder coating system includes booths, conveyors, washers, and dryers. Booths are used to contain overspray and prevent contamination, while conveyors are used to move parts through the system. Washers and dryers are used to clean and prepare parts before coating.
Powder booths
Manual powder booth
Filter or recycling
Cyclone or filter with recovery
- Made of plastic or steel
- Quick color change
- Low-noise fans
Automatic powder booth
Control units
Reciporators
3D Scanners
- Power & Free or Axial
- Automatic or manual
- Optimal solutions according to customer requirements
- High quality standards
Pretreatment lines
Nano technology (Oxsilan, phosphating)
• Degreasing and pickling
• Iron and zinc phosphating lines
• Without chrome
• Spraying & immersion
• Savings in chemical and water consumption